Search results

I ordered the bolts below from Home Depot to install a similar rack. 1/4in - 20 x 3/4" wide tee bolts from Home Depot

Hey there - when I installed the Keko, I just glued the tailgate seal to the spray in liner. I cleaned the area well with 90% alcohol, and used their adhesive promoter. It's has stuck well. When I initially did the install, I ran out of adhesive promoter. I asked for more, and Keko sent me a...

Looks good! I did the same thing, but your's came out better. I also did the long seam between the bed and rail cap. I used blue painters tape on both sides to contain my mistakes. There's also the big holes to cover on the left and right side of the bulk head. I covered those, inside and...

Mine loosened up a little bit near the tailgate after driving fast on some bumpy roads. The cover opened a little bit on one side. I just had to adjust the span between the sides and tighten it up a little bit. Been fine since.

If I were in your shoes, I'd feel a little better off-roading and jumping after installing the J-Braces.

I used 3/4" thick Delrin plastic. The shims for the front four pockets were 2 7/8" x 1 1/4". The shims for the back two pockets were slightly less thick, maybe 1/8" less. I didn't write down the dimensions of the last two, I apologize. The last two thinner ones were a pain in the butt for...

Correct, except my cover is slightly different, the brand is Willmoso. I contacted the company I bought it from (Sadeloos - bought through Temu - ugh!!) to purchase additional brackets. I'll tell you, it was a weird transaction, but I was able to get them and they were inexpensive. I did this...

Does not look like Ford has the J-Braces for Raptor in stock.

Hey good news, my Raptor is fixed and I got it back an hour ago. Dealer somehow had the part in stock. The dealer said the same thing happened to another ranger and the person never brought their truck back to get it fixed, so they used the part for my truck. Weird, but I'll take it!

Well they didn't offer and unfortunately it didn't occur to me to ask...

About a week ago, I got an error on the dash that said the Collision Warning system has detected either a system fault or an obstructed radar sensor. Got a message in Ford Pass to clean the sensor and the windshield where the camera is. Did that, and the fault went away from the dash. I...

Wow, that's strange it's not working.

From there, don't you just press and hold "OK" on the steering wheel?

I removed a couple of those hooks/bolts to install a Ford pivot tool box in my truck bed with Ford factory spray bed liner. The bolts are certainly a pain, but I just took my time and they came out fine. I used a dremel cutting tool to cut the spray liner just between the hook and bolt, then...

Good for you for doing it yourself! It took me a while too, but certainly glad to check it off the list!

Hey there - I didn't do anything beyond what I described, no grommets. If the stake bed caps and the sides are sealed, nothing is going to leak down to the holes. If the holes are filled with grommets, but the stake bed caps are leaking above them, water is still going to get in. The problem...

I have the tonneau from the thread linked below. There's pictures of mine in that thread, if you zoom in you can see the black silicone between the trim and bed. The gorilla tape isn't visible, it's way up near the bulkhead covering the large openings on the left and right. Some people say...

Hey Charley - I'm not sure if there is a brand name, they were super cheap off Temu (Ugh!). Temu threw a discount at me when I bought the tonneau and the cross bars cost $100. They attach in the T Slots of the tonneau. The bolts the cross bars shipped with were for a larger T Slot, so I...

That's what I did and it worked. I used blue painters tape - masked the trim pieces and masked the top edge of the bed, and carefully applied neutral curing black silicone in the gap. I then carefully filled the gaps in the 6 stake pocket caps. I also used Gorilla Waterproof patch and seal...

It will still leak water through the stake pocket caps and some through the sides of the trim even after sealing all those holes. I've found using (neutral curing) silicone on the stake pocket caps and between the outside plastic trim and top of the bed, eliminates the need to seal all those...