Search results

Thanks for taking the time to reply with so much information! Definitely understand it wont be a step up in comfort, but also don't expect it to be uncomfortable--ultimately doing this because the amount of sag with my 3,000 lbs loaded trailer + what I have in my bed looks.... not healthy for...

Do you have a write up on your install? I just ordered the boss to address some sag when towing. Do you have the two lines joined together or do you inflate them individually? I think the boss kit comes with the intention to plumb and fill individually. curious what you used to join them...

I went through the grommet by the steering column. Ground right above where the grommet is, positive to the pre-wired #2 (IIRC) overhead switch. This is on a raptor, don't think other models have the switches. On the raptor there was plenty of room in the grommet, there is a little nub / space...

some aluminum flat bar and an M8 tap from home depot has helped me mount things on the molle panels without drilling into the panels themselves. Bracket is the best solution for sure, but when one isn't available I'd always go that route vs drilling the panels directly. Multiple ways of...

here are the photos you requested (and more). Any questions, let me know.

Mine is a DT35. Sorry typo before edit.

It's currently raining outside. I'll get some more detailed photos for you this weekend when weather permits. As for the questions I can answer right now, 2. - Yes the sliders lock in the extended position. They have a little bit of play from side to side when fully extended and locked if you...

Finally got my bed slide installed, along with some test fitting of my fridge and other items. Very strong slides. I was able to stand on them when they were collapsed in the bed of my truck. Install was straight forward. I like how low profile they are and the efficient use of space. I was...

I don't have the equipment to measure it, but I'd guess not great. I know there are issues with where I placed it, but I use my radio a hand full of times. a year when on trips with friends. I have other stuff I mount on the bed of my truck on these trips that I wanted to keep clear of. I may...

Under the front passenger seat. Used large zip ties to strap it up there. I have the BTECH GMRS 50-pro. All controls are on the handset.

IIRC the Rivnuts are for if you want to use the packout attachment / adapter as per the instructions..

i used an adjustable wrench. I added a string to it and tied it to my wrist (important!!!) so that i wouldn't lose it down between the cab and bed. I then used some gorilla tape or similar, put the nut in the wrench, laid the tape over the back side of the nut & jaws of the wrench to hold it...

I had similar symptoms on one of my other vehicles when a rodent chewed on a couple wires. Was a pain to trouble shoot / diagnose and was very intermittent. Didn't chew all the way through, but just enough to cause all sort of sputtering, cutting out and error codes. Mostly cylinder pressure...

Looks good! Good luck running the wire. It's not horrible.. easier than breaking through the front firewall, at least for me. I added my GMRS antenna like this: I used this bracket and some creative use of bolts, multiple nuts to create stand offs and locknuts...

I get this when towing. I usually click OK and it goes away. Everything is working fine. Only happens for me when something is plugged in, so figured it's a slight voltage fluctuation that is triggering something. Will check with my dealer to see if there is a module update as well next time I...

I don't want to tie up two perfectly good 15A circuits on what is effectively a 6-10 amp load. I ended up going with the below. It takes in a single 7-28v input and splits it into two outputs that can be toggled between by cycling power within 1 sec. It's pricey, but pretty specific and...

Looks good. Too bad nacho doesn't publish the lux measurements (that I could find). That'd be a useful comparison. I'm going to grab 4 of the amber backlight / white scene lights for my AAL bed rails. Just need to figure out a solution to toggle between - off / backlight / on - with one of the...

Is that the amber on high?

This is a potential fix for any issues with fatigue. https://www.ranger6g.com/forum/threads/installed-2024-ranger-xlt-openpilot-level-2-adas-blue-cruise-alternative.16134/page-2#post-247866

The government doesn't dictate engineering. They specify fuel mileage (in this case) and emissions requirements. Agree or disagree with such requirements, the manufacturers then engineer to meet it. Not sure how fuel mileage requirements become "the government dictates oil viscosity". I mean...