Search results

Does anyone know the part number of the yellow stuff brake pads that fit the 24 RR? EBC's site says it is DP42445R, but then Automotive stuff says it is EBC Brakes DP43107R. On another site, the later part number says it does not fit. Can someone please give me an answer who has installed...

Not much pisses me off more than Big Government Fascist crap.

I installed this kit and it works well enough. It does not interfere with the struts either for me. However, it still has gaps that allow dust in, so I bought some extra molding on amazon and added it wherever it was needed. Now it seals perfectly and absolutely no dust gets past. Below are the...

$3K for fender flares, WTF, they carbon? Also, it's too bad you have those weird rules down there regarding poke and eng certs needed. Gotta love the government trying to "protect: you.

Nobody has any idea on this?

Thanks for the tip.

I think I am going to do this. I wonder if Rhino looks more fine grained texture. I would have to compare them. I wonder what Ford used on the running boards, I would want to match that exactly if possible. Does anyone know what is used on the Running boards of the RR?

What did you use for this, is is Raptor, Rhino, what? Look good and I am thinking about doing the same thing.

No fender flares, that is just the stock fenders on the Raptor.

This is 18x9 with 0 offset with 35 x 12.5 tires.

I travel with my dogs a lot. I use rover.com to find people who have doggie daycare right in their house. These are my two boys below.

I have this installed and us the XB Bluetooth dongle that reads the CAN signals and kicks on the lightbar when I activate the high beams. You can add power units as well for other lights. It read things like backup lights, break lights, hazards, etc. https://www.xbb.se/en/xbb-dongle-xbb-powerunit/

I have search high and low and found nothing. This is canbus triggered, so I used the XBB trigger. It does many other things and you can setup several power units to trigger for many things like brake lights, reverse, high beams, etc. https://www.xbb.se/en/xbb-dongle-xbb-powerunit/

I like the Rival one better as well. Also, the price is way up there. More power to them if they can move them at that price, but not sure how many they can move. This is like the Fabulous Fab guys in Australia selling that exhaust for like 7K. Not sure how these companies can move enough...

According to JL Audio's specs the 10TW1-2 is a 2 ohms sub. Any idea on why the installer would have said it is 4 ohms?

I tried everything I could think of, but found no way to do this. I ended using a canbus adapter that plugs into the ODBII port and send a signal to a relay to power on my lights. The cool thing is that it does many vehicle functions. I used it for the high beams and added another relay to work...

That sucks. I had the opposite. I ran the cables and it took like 45 min to get totally done. I run BluePilot on the WD40 model. I changed the various blend factors and it work great now. I drove for 300 miles of mostly freeway and highway and worked like 95% of the time without me touching...

One other thing, what do you guys think regarding putting one under the truck with a fan verses one in front of the radiator/ac condenser? I think I would rather have a fan one underneath or elsewhere rather than in front of the radiator.

When I am in Baha mode, the temps get around 225 to 230 a lot. This happens also when I am in snow and spinning the tranny at high RPMs. I saw it get to like 240, so I chilled out on the throttle until is cooled a bit. Is this normal or in any way damaging? 230 is not that hot, but doing this...

I can definitely see that. It would then be a good excuse to buy some of the Foutz replacements.