Search results

Maybe the sleep mode. Just riding my motorcycle for the Summer.

I think I know about that switch. Maybe I have pushed it in correctly while trying to find the back window switch. Thanks !

Battery is fine. I can turn dome light on manually. How do you get it to turn on automatically when entering truck.

Maybe the front dome light has three modes. I am just switching it on and off. Irritating when entering vehicle and interior lights do not come on. I am more old school. Yes that's a high and low beam on floor.

What am i missing. Is this with in Screen settings. When entering the vehicle the dome lights do not turn on automatically. 2025 XLT MPC 2.3L

Ranger Roof Rack Install without dropping headliner... Front Runner SlimSport - YouTube My truck has to get under my apartment parking gate. The Slim Sport Rack is under 3" high. I used the partial head linear video as reference. The Ditch Trim holes have to be drilled to fit the 8mm bolt. On...

Strange, maybe the roof trim was removed. I put a Slim Line 2 roof rack on. That location is where there is a hole in roof for black trim. This picture is at the front. There are 4 holes in roof for Ditch trim. Two holes on each side.

Poor Drivers in the Lower Mainland. Some of these Dump trucks they do not service correctly. Enjoy seeing these trucks pulled over for inspection. Good in BC they I think charge the companies that hit the over passes. Good thing I have a short commute. Let's just keep cramming more people into...

I cannot see from the pinch weld view. It looks like they just sandwich on to the pinch weld. Instead of drilling into it. I would say the Raptor Frame Sliders are similar to the issues i had. I stopped because i wish things done to my perfection as a Machinist. I can also see the same issue I...

Being at tall person The front window pillar sloping back causes issues to get in. I have to put my head in first. It may help to have the truck lifted.

I was not too happy the Pinch weld system was off. As you can see i damaged the pinch weld in just one area. Knew when to stop. I expect them to attach correctly to pinch weld. How many people have access to a 90 degree drill. Plus you have to have equipment around to cut a drill in half. Then...

i am a Machinist. I contacted Rocky Road Adventures and told and showed them of how the welding fixture needed to be adjusted to make the Pinch Weld part of it work correctly. An adjustment of 1/8" up on holes and front two brackets moved in 1/8". I wanted to improve the Pinch weld system for...

I ordered my XLT. No rust on Drive Shaft. I painted it and went over with a brush on the fasteners that rust. Like the ones on the brake backing plates. The mufflers rust out. Still want to spray it with some heat paint.

Yes the bed extender will flip into box. I have this one for many years. Ramp/ Bed extender. Ready Ramp. A good item for motorcycles is an angle iron bracket with tie down points close to tire. i purchased one, it had a tire cut out also. goes behind cab high on bed. I could not find the...

It does not seem to be mentioned that the pinch weld sytem is not designed correctly. Look at the pictures of the gap from the pinch weld on @Icemilkteaa Raptor. I sent Rocky Road Outfitters a message to there Plant Manager Matt Frisby. Showing them the issue with the pinch weld system and...

It would have been nice if Ford put some increments on those gauges. At least give us a reference of what half way reads. I guess if you are right at the top then there's a problem.

I do not like the mixing of Metric and Standard. I put a drop of Red Loctite on M10 Bolts. Did not tighten them with Torque Wrench. I have learned that from working on motorcycles. No 1/2" drive. With 3/8" drive I tighten them firmly. Would have liked the sliders to stick out a bit more. I...

I did not wish to show this photo picture. A mess. Created large Burrs. Hard to remove. I made sure I painted this to seal it. Did this once then stopped.

If members are having them made which takes 2 months, I would send them this thread and say these modifications need to be done. The stepped out at the back mounts does not help. Front two brackets need to be brought in. Holes need to be put higher by 1/8" and backing brackets need to be made...