What did you do to your Ranger Raptor Today?

[Ford Motor Company]

I haven't done anything to mine yet, as I just bought it last week.
However, I have finished reading this entire thread and have about 25 things I want to do now, so thanks for that!

Quick question, what is the running rate to get PPF done?
I have been contemplating just getting the front done, maybe ceramic coating, or full PPF.
I don't know enough about it so I figure you guys have been through this. Any pointers?

Congratulations on your new Ranger! Hope you love it just as much as we do.

Sponsored

 

[three west]

Little things can make a big difference! Is there anyway to check that those are accurate fuse labels? I didn’t see much info in the paper manual… trying to figure out what type of relay (1,2,or3) I have for the starter..

Fair question, and I have no idea. I know the vendor has some standing with the Bronco crowd, so I took it on faith and slapped them on.

 

[Full-size no more]

Fair question, and I have no idea. I know the vendor has some standing with the Bronco crowd, so I took it on faith and slapped them on.

Would you mind posting a picture of the labels close up? I don’t want to blindly pull relays if I can at least get an idea of where they are.. so far this is all I found and didn’t really help (first pic is engine bay, 2nd is interior)

 

[Machduty]

Added upr dual valve catch can. I'll tackle the clean side separator tomorrow.

 

[RANGER/HOBB]

Added upr dual valve catch can. I'll tackle the clean side separator tomorrow.

A question if you don’t mind;

The additional tube for the intake, did you have to drill into the intake tube as shown? I haven’t looked at the intake tubing right yet and simply don’t know.

 

[Machduty]

A question if you don’t mind;

The additional tube for the intake, did you have to drill into the intake tube as shown? I have looked at the intake tubing right yet and simply don’t know.aUOR doesn’t offer the install instructions online that I can see.

Yes I drilled a hole with a 7/8" bit.

 

[three west]

Would you mind posting a picture of the labels close up? I don’t want to blindly pull relays if I can at least get an idea of where they are.. so far this is all I found and didn’t really help (first pic is engine bay, 2nd is interior)

Here you go

 

[jmatthew]

It’s little wonder the USA still has the strongest economy in the world .
You guys buying sh1t to bolt to your rangers is playing a big part.

Everyone has to do their part.

 

[jmatthew]

Added the stealth light bar today, gonna test it out tonight. No interference with the shutters or any other piece. Took around 40 minutes to install.

What light bar did you get?

 

[Hyperbolic_1]

I finally (!!!) got my RR and immediately (i.e., before it left the dealership) swapped out the stock 285/70R17 KO3s with 285/75R17 KO3s. Same width, 1" taller, and picked up the white raised lettering (I prefer the old school look) and a load E rating. In my opinion, this is the tire size they should have shipped with.

Next up is painting the skid plate and lower bumper black with sprain-on bed liner, adding frame mounted rock sliders / side steps and some RPG adjustable perch collars to take out most of the rake as she has settled more since these pics were taken. Adjustable since eventually I plan to get an A.R.E. CX topper and will likely need to adjust collars to maintain near level look.

Lastly, just for comparison, a few pics of my RR with my dad's 2020 Ranger.

 

[Ford Motor Company]

I finally (!!!) got my RR and immediately (i.e., before it left the dealership) swapped out the stock 285/70R17 KO3s with 285/75R17 KO3s. Same width, 1" taller, and picked up the white raised lettering (I prefer the old school look) and a load E rating. In my opinion, this is the tire size they should have shipped with.

Next up is painting the skid plate and lower bumper black with sprain-on bed liner, adding frame mounted rock sliders / side steps and some RPG adjustable perch collars to take out most of the rake as she has settled more since these pics were taken. Adjustable since eventually I plan to get an A.R.E. CX topper and will likely need to adjust collars to maintain near level look.

Lastly, just for comparison, a few pics of my RR with my dad's 2020 Ranger.

Great pics! Thanks for sharing these with us! 🛻

 

[Full-size no more]

Here you go

Thank you!!

 

[GigaRaptor]

Installed EGR Rolltrac (manual) and Kuat Ibex. The fit and finish of both of these products is really impressive.

 

[RogueLobo]

Installed EGR Rolltrac (manual) and Kuat Ibex. The fit and finish of both of these products is really impressive.

GigaRaptor, this cover looks great! Could you please post a couple pics with cover open looking into bed to see storage can? Thanks!

 

[RANGER/HOBB]

Yes I drilled a hole with a 7/8" bit.

Finally found the instructions………..Thank You!

Sponsored