ADD Edge Bumper + Nacho Grande Supreme 100 Lights installed

modified_rraptor · Jul 18, 2025

I finally got around to installing my ADD Edge front bumper paired with 4 x Nacho Grande Supreme 100 lights in the bumper and 2 x Nacho Quattro Supreme lights on the a-pillars to replace my Diode Dynamics SS3 Max. The light output is incredible.

A few people have commented on the lack of “intercooler flow”, if you’re in that boat, this bumper isn’t for you because no one can change your mind. We drive a ranger raptor not a drag car looking for tenths in the 1/4 mile. However I do live in one of the hottest parts of Arizona and I can’t differentiate from before or after the bumper install on my pulls getting onto the freeway/desert running.

Anyways, feel free to ask me any questions you may have!

BeetleThighs · Jul 19, 2025

Looks great! I've been waiting to see those Nacho Quatro's on the A-Pillar on a RR for sometime. How do they compare to your previous Diode Dynamics in terms of light output... and diode dynamics DLR backlight versus the Nacho's TLR??

Do you have an pics with the Amber Lens cover on the Ditch Lights?

modified_rraptor · Jul 19, 2025

BeetleThighs said:
Looks great! I've been waiting to see those Nacho Quatro's on the A-Pillar on a RR for sometime. How do they compare to your previous Diode Dynamics in terms of light output... and diode dynamics DLR backlight versus the Nacho's TLR??

Do you have an pics with the Amber Lens cover on the Ditch Lights?

Thank you! The light output difference is insane. I believed the SS3 Max’s were just about the brightest in the category, but these blow them out of the water. As far as looks, these supremes with the exoskeleton are definitely bigger, but IMO it’s worth it for their light output.

DLR vs TLR, I’d say the TLR in the Nacho fills out more of the lens due to more backlit leds.

I haven’t taken any pictures with the amber lens covers installed yet.

JDRR25 · Jul 20, 2025

Looks phenomenal!

YukonRanger · Jul 20, 2025

This is the bumper i've been eyeing.... looks great!

Couple questions:

-is the front skidplate on that setup replaceable or do you need whole new bumper if you bash it?
-how difficult was the install, any cutting required?

395N · Jul 20, 2025

Looks wonderful. Perfect if you will.

Slyder · Jul 20, 2025

YukonRanger said:
This is the bumper i've been eyeing.... looks great!

Couple questions:

-is the front skidplate on that setup replaceable or do you need whole new bumper if you bash it?
-how difficult was the install, any cutting required?

The skid-plate is replaceable and removable, but not as 'easy to remove' as ADD claims.

1) Unless you got unnaturally skinny and long fingers, the grill has to come out for you to access a good portion of the skidplate's bolts or to adjust your lights (in the event one comes in contact with something and ends up moving it)

I have this bumper with Rigid 360's on my truck, so I learned this the hard way.

2) The only so called cutting that's needed is to trim the fender liners a bit so they're not so visible below the bumpers angled ends.
::Edit:: I forgot you need to notch the factory skidplate to access a Factory hole to bolt down the ADD one. I have the Rival skidplate, so I had to notch the U-bracket/spacer instead.

Desertrunner21 · Jul 20, 2025

Looks bad ass!! More pictures please. Specially close ups showing the skid plate.
How’s the opening to allow air to the intercooler?

Desertrunner21 · Jul 20, 2025

Also how well does your lane centering and adaptive cruise control work now?

RaptrJr · Jul 21, 2025

Bumper looks great! The airflow does bother me a little bit not going to lie but it looks like there's some areas in the skid plate to let some air flow too which is nice! What did you do with the fog light wiring? I assume it just gets tucked away somewhere?

Not trying to thread jack are there any pictures with the Baja Designs LP4's? All my lights are BD so that's the light I would get.

Havasu RR · Jul 21, 2025

modified_rraptor said:
I finally got around to installing my ADD Edge front bumper paired with 4 x Nacho Grande Supreme 100 lights in the bumper and 2 x Nacho Quattro Supreme lights on the a-pillars to replace my Diode Dynamics SS3 Max. The light output is incredible.

A few people have commented on the lack of “intercooler flow”, if you’re in that boat, this bumper isn’t for you because no one can change your mind. We drive a ranger raptor not a drag car looking for tenths in the 1/4 mile. However I do live in one of the hottest parts of Arizona and I can’t differentiate from before or after the bumper install on my pulls getting onto the freeway/desert running.

Anyways, feel free to ask me any questions you may have!

That looks really good. But damn they are spendy... But damn they look good

Rousseb90 · Jul 28, 2025

Saw a video on this today on YouTube. Piss poor design on some of the mounts as well as the sensors from what I saw. Any insight?

pablo94sc · Jul 28, 2025

That looks slick.

RaptrJr · Jul 29, 2025

Rousseb90 said:
Saw a video on this today on YouTube. Piss poor design on some of the mounts as well as the sensors from what I saw. Any insight?

which video are you talking about?

Rousseb90 · Jul 29, 2025

RaptrJr said:
which video are you talking about?

ADD Edge Bumper + Nacho Grande Supreme 100 Lights installed

modified_rraptor

Active Member

BeetleThighs

Well-Known Member

modified_rraptor

Active Member

JDRR25

New Member

YukonRanger

Well-Known Member

395N

Active Member

Slyder

Well-Known Member

Desertrunner21

Well-Known Member

Desertrunner21

Well-Known Member

RaptrJr

Well-Known Member

Havasu RR

Well-Known Member

Rousseb90

Well-Known Member

pablo94sc

Well-Known Member

RaptrJr

Well-Known Member

Rousseb90

Well-Known Member

Similar threads