What did you do to your Ranger Raptor Today?

[be.jammmin]

Added a few visual mods and did a full wash, decontamination, paint correction, polish and C6 Hyrdo Lite ceramic. It’s slowly getting there.

Sponsored

 

[GigaRaptor]

Test fitted my JDScustom “Raptor” dune flag mounting bracket and installed F150LEDs.com 3 light kit.

 

[SyphioD]

GFC Install today at Stellar Built Sacramento!

Been wondering if anyone else had a wedge camper fitted to a 2024 Ranger yet. The GFC looks great.

I am considering the Oru designs bruin but a bit concerned with how it will have straight sidewalls and a pretty large platform over the cab. For now I've got the j-braces ordered with points, probably won't move on a wedge order until closer to fall.

What I did do to my RR today is actually drive it since purchasing Friday. The excitement of owning this vehicle is finally starting to hit me after being too busy to give it any attention the past two days.

 

[Ford Motor Company]

Painted the rings to match.

That small detail makes a big difference, Dave! Great looking Ranger .

 

[Arsenall11]

That small detail makes a big difference, Dave! Great looking Ranger .

Thank you! I have had every generation of the F150 in Lariats going back to 86, this is by far the best built, the F-150 were all great too but the quality on this one you knocked it out of the park!

 

[Ford Motor Company]

I finally got my new wheels!

Black Rhino Etosha wheel w/+20mm offset. The wheel fits perfectly, and as you can see from the picture with the level, the tread pattern sits almost flush with the top of the wheel arch. I also used the stock KO3 tires.

I'm so happy with it, and the bronze wheel on Cactus Gray looks sooo good!

Sweet ride! ?

 

[welker]

Installed a few things this past weekend...

@GregFoutz Collars, 2.5" Fronts and 2.0" Rears. The combo worked out to right on 2.5" of actual lift in the front and about 1.25-1.5" in the rear. Truck still has about a 2" rake, which is about what I was going for so I don't sag when loaded up.

Some Baja Designs S1 Flusmount's wired into AUX4

And a couple of Diode Dynamics Stage Series Rock Lights under the hood.

I was thinking about throwing some S2 flush mounts in the same location, is there a reason you went with S1s?

 

[mtesni]

I was thinking about throwing some S2 flush mounts in the same location, is there a reason you went with S1s?

I wanted to be able to fit a 35" Spare in the stock location and figured the smaller lights gave me some more room. As it was I had to rotate the passenger side one 90° to get it to clear the tire. Edited to add: The S1's are also priced like the S2 Sports but are listed with the similar lumen output as the S2 Pros.

(Drivers Side rotated for my own need for symmetry lol)

 

[welker]

I wanted to be able to fit a 35" Spare in the stock location and figured the smaller lights gave me some more room. As it was I had to rotate the passenger side one 90° to get it to clear the tire.

(Drivers Side rotated for my own need for symmetry lol)

I didn't even consider that, I haven't checked the clearance again since I put my 35 under there. I will have to mock it up again and hopefully not learn a hard lesson about cutting before you are 100% something will fit lol

 

[ADDGAMER]

YowieDrive/DingoTrails neoprene seat covers

How did you get these shipped to the US? Can't seem to get anyone to send these center console covers delivered to the US.

 

[yoopercharged]

Installed a few things this past weekend...

@GregFoutz Collars, 2.5" Fronts and 2.0" Rears. The combo worked out to right on 2.5" of actual lift in the front and about 1.25-1.5" in the rear. Truck still has about a 2" rake, which is about what I was going for so I don't sag when loaded up.

Some Baja Designs S1 Flusmount's wired into AUX4

And a couple of Diode Dynamics Stage Series Rock Lights under the hood.

How sketchy was it to mount the 2.5" collars without a wall mounted compressor?

 

[Joejr]

Just put some decals on ford grille to add a little pop.

 

[a77cj7]

How sketchy was it to mount the 2.5" collars without a wall mounted compressor?

I installed mine with this style compressor:

Always a bit clumsy to get fitted, but it scares me less than the individual style.

 

[Arsenall11]

Smoked the third brake light with matte peal light spray. The third is still bright.

 

[Arsenall11]

Not sure I posted this added the Builtrite molle to the bed, waiting on the rear drivers side piece to be released.

Sponsored