Sponsored

J&L dual catch can yay or nay?

ksale29

Well-Known Member
First Name
Keith
Joined
Jul 5, 2026
Threads
4
Messages
53
Reaction score
54
Location
Panama City Florida
Vehicle(s)
2026 Ranger Rapture
I saw the video where the guy had a J&L single valve catch can and his valves were still coated with oil sludge and he was thinking about going to a dual valve. So I ordered UPR dual valve not realizing that it requires drilling you know because it's "plug n play". I'm a little hesitant about installing it and was wanting to hear some opinions. I'm neutral at this point.
Sponsored

 

superj

Well-Known Member
First Name
Jason
Joined
Feb 8, 2025
Threads
46
Messages
4,134
Reaction score
4,025
Location
Corpus christi texas
Vehicle(s)
2024 ford ranger, 2019 wrangler, 2018 mazda3
Occupation
Retired
Even with a catch can, you will still get build up in the valves. It won't keep them clean.

It just slows down the build up.

As far as the dual can, I have no idea. I had a single can on my v8 Nissan truck and thought it was very nice and only emptied it every 5k miles and it had about half an inch of fluid in it
 

CoastieN70

Well-Known Member
First Name
Lee
Joined
May 31, 2019
Threads
6
Messages
450
Reaction score
157
Location
Travelers Rest, SC
Vehicle(s)
2025 Ranger Raptor
Occupation
Retired U.S. Coast Guard
I have the UPR Dual Catch Can installed. The drilling is in the passenger side intake hose. It is not difficult and the hole drilled is to install a fitting for the wide-open throttle side.
The only caution I have is that you MUST wipe clean any debris from the drilling of the hose before reinstalling the hose. The whole installation took about an hour and a half and I'm an old guy :)
I get about two once's of oily gunk from the can every 5000 miles. That may not sound like much BUT it really is a lot where the valves are concerned.
BTW: just break the OEM hose fittings instead of trying to "dismantle" them, it makes the whole project go MUCH quicker and the likelihood of reversing the installation is nil.
 
OP
OP
ksale29

ksale29

Well-Known Member
First Name
Keith
Joined
Jul 5, 2026
Threads
4
Messages
53
Reaction score
54
Location
Panama City Florida
Vehicle(s)
2026 Ranger Rapture
I have the UPR Dual Catch Can installed. The drilling is in the passenger side intake hose. It is not difficult and the hole drilled is to install a fitting for the wide-open throttle side.
The only caution I have is that you MUST wipe clean any debris from the drilling of the hose before reinstalling the hose. The whole installation took about an hour and a half and I'm an old guy :)
I get about two once's of oily gunk from the can every 5000 miles. That may not sound like much BUT it really is a lot where the valves are concerned.
BTW: just break the OEM hose fittings instead of trying to "dismantle" them, it makes the whole project go MUCH quicker and the likelihood of reversing the installation is nil.
Good stuff thank you. I'm not so much worried about being able to do the install as I am drilling into the stock inlet and breaking the OEM fitting If it's worth it for the dual vs the single. Does the dual make it worth the modifications or would I get similar to the same results with the single can. I can't find much information to support either to be honest.
 

Sponsored

sweeks888

Well-Known Member
First Name
Steve
Joined
Mar 6, 2025
Threads
4
Messages
173
Reaction score
158
Location
Richland, WA
Vehicle(s)
2024 Ford Ranger Raptor
Occupation
Retired
I saw the video where the guy had a J&L single valve catch can and his valves were still coated with oil sludge and he was thinking about going to a dual valve. So I ordered UPR dual valve not realizing that it requires drilling you know because it's "plug n play". I'm a little hesitant about installing it and was wanting to hear some opinions. I'm neutral at this point.
I went this route instead (assume we're talking about the same thing), since the idea of having to empty a reservoir every oil change didn't appeal to me. A little spendy, but install and forget it. Also no drilling, comes with all necessary hardware for installation. Took a little while to get everything implemented correctly (I like to take my time for perfection), but never any issues since installation and would do it again...

https://www.iagoffroad.com/products...024-ford-ranger-raptor?variant=43392480903231
 
OP
OP
ksale29

ksale29

Well-Known Member
First Name
Keith
Joined
Jul 5, 2026
Threads
4
Messages
53
Reaction score
54
Location
Panama City Florida
Vehicle(s)
2026 Ranger Rapture
I went this route instead (assume we're talking about the same thing), since the idea of having to empty a reservoir every oil change didn't appeal to me. A little spendy, but install and forget it. Also no drilling, comes with all necessary hardware for installation. Took a little while to get everything implemented correctly (I like to take my time for perfection), but never any issues since installation and would do it again...

https://www.iagoffroad.com/products...024-ford-ranger-raptor?variant=43392480903231
Thank you! I haven't seen these before. The one I purchased from UPR was around $390. Not having to do any permanent modifications or worrying about emptying a catch can would be worth $100 to me.
 

sweeks888

Well-Known Member
First Name
Steve
Joined
Mar 6, 2025
Threads
4
Messages
173
Reaction score
158
Location
Richland, WA
Vehicle(s)
2024 Ford Ranger Raptor
Occupation
Retired
Thank you! I haven't seen these before. The one I purchased from UPR was around $390. Not having to do any permanent modifications or worrying about emptying a catch can would be worth $100 to me.
Was exactly my thought as well. Came with everything needed, so original hoses, hardware could be kept as needed. Hard to see in the pic, but where they said to mount it, it fit perfect with the included bracket.
Ford Ranger J&L dual catch can yay or nay? Ford Ranger Rapter Catch Can Installed
 
OP
OP
ksale29

ksale29

Well-Known Member
First Name
Keith
Joined
Jul 5, 2026
Threads
4
Messages
53
Reaction score
54
Location
Panama City Florida
Vehicle(s)
2026 Ranger Rapture
Was exactly my thought as well. Came with everything needed, so original hoses, hardware could be kept as needed. Hard to see in the pic, but where they said to mount it, it fit perfect with the included bracket.
Ford Ranger Rapter Catch Can Installed.webp
The website says 24+ but at the bottom says doesn't fit 26. I'm going to verify tomorrow and if it fits I believe that's what I want to go with.
 

Sponsored

Buellsox

Well-Known Member
First Name
Scott
Joined
Oct 22, 2025
Threads
4
Messages
292
Reaction score
440
Location
Tacoma, WA
Vehicle(s)
2025 Ranger Raptor
Occupation
Local 26 Union Plumber
The IAG is a perfect unit for dual side catchment and you never have to empty it. Plus it’s heated. Took under 2 hours to install and I can guarantee is 100% P&P! Zero drilling or remodification of anything factory. Been a bulletproof install & purchase.

Ford Ranger J&L dual catch can yay or nay? IMG_1108


Ford Ranger J&L dual catch can yay or nay? IMG_1109


Ford Ranger J&L dual catch can yay or nay? IMG_1110
 
OP
OP
ksale29

ksale29

Well-Known Member
First Name
Keith
Joined
Jul 5, 2026
Threads
4
Messages
53
Reaction score
54
Location
Panama City Florida
Vehicle(s)
2026 Ranger Rapture
If I can confirm tomorrow that this will fit the 26 I will definitely be ordering. Thank you!
 

got3fords

Well-Known Member
First Name
James
Joined
Jan 30, 2025
Threads
28
Messages
774
Reaction score
686
Location
Central Va.
Vehicle(s)
2026 Ranger Raptor
I went this route instead (assume we're talking about the same thing), since the idea of having to empty a reservoir every oil change didn't appeal to me. A little spendy, but install and forget it. Also no drilling, comes with all necessary hardware for installation. Took a little while to get everything implemented correctly (I like to take my time for perfection), but never any issues since installation and would do it again...

https://www.iagoffroad.com/products...024-ford-ranger-raptor?variant=43392480903231
That is a serious looking product. If I were to add such a device, I would probably go with this. How long did the install take?
 

Buellsox

Well-Known Member
First Name
Scott
Joined
Oct 22, 2025
Threads
4
Messages
292
Reaction score
440
Location
Tacoma, WA
Vehicle(s)
2025 Ranger Raptor
Occupation
Local 26 Union Plumber
That is a serious looking product. If I were to add such a device, I would probably go with this. How long did the install take?
I had my IAG in start to finish in just about 2 hours. And that was taking my time with the steps, along with detailing along the way, and repositioning clamps, etc.
The manufacturer has detailed step by step instructions on their website so you can check out the involvement beforehand.
 
 







Top