FORScan NA Ranger 6th Gen (2024+) Crowdsourced Spreadsheet

[Raptortugal]

I managed to remove the CAMERA AUX icon in 7D0-01-02 I left by default 2xxx instead of Axxx (2 being aux camera disabled).
I will also modify everything related to the CAMERA AUX in the IPMA by comparing with the original.

Sponsored

 

[babaduk]

anyone know how to enable 50/50 view camera?
any help much appreciated

 

[pablo94sc]

It’s not in your manual, it’s not intended that way, so the dealer can’t repair anything. Everything is working as designed. And there is no coding for it in FORScan.

It may not be in the manual, but some modes, like Slippery, say press OK on restarts. It only lasts about 4 seconds.

 

[Ag3ntC00p3r]

It may not be in the manual, but some modes, like Slippery, say press OK on restarts. It only lasts about 4 seconds.

Correct. And if you don’t have the seat belt message disabled it’s impossible to even hit OK on that screen.

 

[sloon]

Can someone remind me where to find the codes for enabling the actual numerical temp for engine and oil in the dash display?

Digital Temp Gauge (With Alphabet C/H, E/F)	IPC	720-07-01	xxxx-xx**-xxxx	**=54
Minor Gauge Units (Numerical/ Alphabet C/H, E/F)	IPC	720-11-01	xxxx-xxxx-*xxx	Alphabet *=8 / Numerical *=A

 

[Sequoia]

Does anyone know if it’s possible to code the daytime running LEDs not to dim when the low beams are on?

 

[craigc]

Now it would be brilliant to make the front camera activatable as well.

I've tried everything I know to try and have not yet been able to get the front camera at speed...

If anyone has had trouble getting the "reverse camera at speed", this is how I got it working on MY22 XLT

IPMA 706-02-02 xxxF CExx xx--
APIM 7D0-01-01 xxxx xxxx Fx--
APIM 7D0-01-02 Axxx xxxx xx--
APIM 7D0-01-04 xxxx FCxx xx--
APIM 7D0-02-02 xxx3 xxxx xx--

As always use at your own risk

I'll try to find some time this week to add this to the sheet

 

[craigc]

It is like the truck knows you are on a freeway and automatically goes into Auto Resume mode for adaptive cruise control. Then when the car in front moves, it start to accelerate from a stop automatically. But, when on normal streets, it knows and when it comes to a stop it goes to Auto Stop and you have to either press the gas or kit OK on the steering wheel to have the truck start again when the car in front start to move.

I'm not positive, but I think it has to do with whether you step on the brake or it automatically stops you as traffic ahead slows/stops. In the city I tend to not trust the ACC stopping me gracefully enough and usually hit the brake with my foot and then I think that won't let me resume until over 20MPH.

 

[craigc]

Can someone remind me where to find the codes for enabling the actual numerical temp for engine and oil in the dash display?

 

[Ragner]

I've tried everything I know to try and have not yet been able to get the front camera at speed...


I'll try to find some time this week to add this to the sheet

It should be noted that 7D0-01-02 should be 2xxx xxxx xx-- instead of A..

This removed the button for auxiliary camera.

 

[Antman450]

I'm not positive, but I think it has to do with whether you step on the brake or it automatically stops you as traffic ahead slows/stops. In the city I tend to not trust the ACC stopping me gracefully enough and usually hit the brake with my foot and then I think that won't let me resume until over 20MPH.

I just let the truck stop on its own when the car in front stops just like on the freeway. However, it does not Auto Resume and I have to hit the gas pedal or "Ok" on the wheel to get it to go again. It does not do this on the freeway and resumes on its own.

I was wondering if anyone knew how to set this with Forscan to do the same as on the freeway. I would imagine there is a setting somewhere for this. I do not however have the knowledge to figure it out.

 

[Sequoia]

I just searched my PDF of the modules. Maybe in BodyCM the point:
"Cruise Control" is set per default to: "Adaptive Cruise control, Stop&Go"
Maybe there is another option?

 

[CarTuner]

Can someone let me know what works on Aussie Rangers?
Sorry if someone's asked this already, I'm lazy...

 

[KiwiRaptor]

Can someone let me know what works on Aussie Rangers?
Sorry if someone's asked this already, I'm lazy...

Mine's an NZ Raptor. Should be similar. Here's what I've got working so far.

Power Delivery (To Wheels) Gauge in Cluster

Turbo Boost Gauge in Cluster

Tow/Haul Mode

Trail Turn Assist

Auto Lock Doors on Motion

Lane Keep Assist Removal

Lane Change Blink Number

Enable Reverse Camera and Hitch View at Speed

Engine Temperature Gauge - Show Temp Value Below Gauge

Transmission Temperature Gauge - Show Temp Value Below Gauge

Fuel Gauge - E to F

Turn Off Seat Belt Reminders

TPMS Default Units - PSI

TPMS - Display tire temperature in addition to tire pressure

Frost Telltale (Below 5 deg) - Not sure if working, since it's summer.

 

[cleffe]

Can you switch Baja mode to allow 4A or 2H?

Sponsored